Repair Pc Not Starting (Solved)

Home > Computer Won 39 T > Pc Not Starting

Pc Not Starting

Contents

Upon Removing the RAM cards, I'm getting the beep errors - so I know, to some degree, that the Mobo is working. Report DJ AKSHAY 266Posts Sunday December 21, 2008Registration date April 26, 2010 Last seen - Mar 2, 2009 at 09:45 AM The 2 beeps are in relation to the graphics card. Click here for instructions on reinstalling Windows Vista. Disconnect, then reconnect the data cable from the socket on the motherboard. have a peek at this web-site

The computer can usually be restarted by turning the power off and then on, but ignoring the error message does not resolve a recurring problem. If you hear beep tones (usually 1 - 6 tones), contact HP to report the number and duration of the tones, and receive technical assistance. Plug the power cable back into the computer. The beep occurs when the cards are out. http://support.hp.com/us-en/document/c01443371

Computer Not Powering On

If the computer still does not start properly, select your symptom from the list below to guide you to the recommended corrective actions. Be careful not to slide skin along any interior metal edge of the computer. Power Supply fine Processor works fine.

Remove any CDs and DVDs from the disc drives. My PC won't boot: Remove any USB drives or memory cards Assuming everything is ok with the power supply and screen, your computer may be getting stuck before it loads Windows. If the computer starts normally after performing a hard reset, you are done troubleshooting. Computer Won't Boot Up Black Screen HAHAHAHAHAHHA- Apr 11, 2009 at 11:38 PM DJ, Just a note to follow up.

I reassembled my pc, and it runs fine but send nothing to my monitor. Computer Won't Boot Windows 7 If you are using Windows Vista or XP, you'll need to boot from the installation disc to access the Startup Repair tools.[3] You can open the Advanced Startup menu by repeatedly Thanks for the same. https://www.lifewire.com/how-to-fix-a-computer-that-wont-turn-on-2624450 Who would think the problem was something I couldn't physically see (static electricity)?

Share Tweet Expert tips for fixing a PC that won't start up PC Advisor Phones Smartphone reviews Best smartphones Smartphone tips Smartphone buying advice Smartphone deals Laptops Laptops reviews Laptops tips Pc Wont Boot To Bios If you can't access the Advanced Startup menu, you may have a problem with your hardware. it's suppose to light right??? Perform Memory and Hard Drive diagnostic tests If there is power to the notebook, you may be able to access the EFI or the BIOS to run memory and hard drive

Computer Won't Boot Windows 7

To be sure if your motherboard is still in good working condition, remove the memory card and power on the PC. http://support.hp.com/us-en/document/c03513214 Connections all look good. Computer Not Powering On Visit now Z7_3054ICK0KGTE30AQO5O3KA30H4 hp-feedback-banner-portlet Actions ${title} Loading... My Computer Wont Turn On And Beeps Video on performing a hard reset on a notebook with a removable battery View this video on YouTube.

IBM WebSphere Portal Home IBM Logo Sign Up Log In Welcome Getting Started Contact HP - Anonymous Contact HP Product Context View Support Home Test page Product Home Product Warranty Result Sometimes the power on light comes on amber not green. Report Subham- Oct 20, 2009 at 01:50 AM Hi Akshay, I found all your repeated response on this forum.Thats really helpful.Thanks for all this.I have similar problem with my PC.As you Here are our expert tips for trying to fix a non-booting laptop or PC. Computer Has Power But Wont Turn On

  1. Einige Desktop-PCs haben keineF12-Taste.
  2. Disconnect all connected devices and cables such as Personal Media Drives, USB drives, printers, and faxes.
  3. For more information about System Recovery, see Performing an HP System Recovery.
  4. Press and hold the Power button for 5 seconds to turn off the computer.
  5. If the test fails, the hard drive might need to be replaced.
  6. Wenn die Betriebsanzeige gelb oder orange leuchtet, ist dies üblicherweise ein Anzeichen für einen nicht bestandenen POST.
  7. The Windows logo appears on a blank screen or a specific error message is displayed.

Select them one at a time and press the enter key to attempt a system restart. Help would be appreciated. If you performed one or more of the troubleshooting processes and your computer booted normally into the Windows operating system, you should do the following to prevent future problems: Run HP Source I took them out and tried to put in a 512 and a 256 but found they were NOT the right ones.

Use a computer with access to the internet to search the following web sites for solutions to the specific error message. Computer Won't Boot Windows 10 Thanks in advance. Remember to ground yourself with an antistatic wriststrap or by touching the exposed metal of the case before touching any internal components. 5 Reseat all of your components.

Report Fran› DJ AKSHAY - Feb 6, 2009 at 02:34 PM I also have a very old gateway computer 1999-2000 almost the same problem with the power button.

Occasionally, people have found that removing the drive and putting it in the freezer for a couple of hours (in a freezer bag) does the trick. Privacy Policy © Copyright 2017 HP Development Company, L.P. Not sure what to tell you. Pc Wont Start I also jst got new ram and psu, but my comp does not make that beep at startup nore does the keyboard and cd drive light come on or work.

Symptom: LEDs blink or computer beeps but does not start Symptom Possible Cause When you press the power button, some of the LED lights on the keyboard blink or a beep Restore the default VGA Low-Resolution graphics settings. Give me feedback on the above for me to be able to help you further but don't worry, I have seen all kinds of problems in my life. What to do when the computer starts into Windows normally If the computer started after performing a Hard Reset and connecting the AC power only, you should shut down the computer,

Report DJ AKSHAY 266Posts Sunday December 21, 2008Registration date April 26, 2010 Last seen - Jul 16, 2009 at 11:26 PM Normally you should use the eraser on the memory card Follow these steps to use the UEFI tests to check for problems: Step 1: Run the System Quick Test in UEFI (All-in-Ones) The System Quick Test takes about 10 minutes to Actions when no error messages display Restart the computer. Unfortunately I don't have a add-in video card or a PSU power enough to supply it.No jumper to reset my BIOS either.And no loose heatsinks and none of the regular capacitors

Complementary Content IBM WebSphere Portal Home IBM Logo Sign Up Log In Welcome Getting Started Contact HP - Anonymous Contact HP Product Context View Support Home Test page Product Home Product